There is a small switch or an infra-red sensor that sees the paper. Check it in the slot of the shredder. Shredderparts.com/ We sell all sizes of paper shredder gears, switches, blades, etc.
To facilitate your repair. We also have shredder replacement parts for crosscut paper shredders.
Www.shredderrepair.co.uk/general-shredder-parts-227-c.asp We can supply a wide selection of parts for various makes of shredder some of the. Paper Shredders. Please note SRS take no responsibility for loss, damage or personal injury caused by the fitting of spare parts by non SRS personnel. Document Dynamix Australia has a strong reputation for responsive supply of paper shredder replacement spare parts and support.
Whatever brand your paper. Jul 17, 2017.
Remove Shredder from paper catcher bin. Remove shredder cover from shredding mechanism assemble (approx.
6 screws on bottom of cover). Separate shredding mechanism from bottom cover (may have disconnect circuit board from assembly and other wiring from switches, sensors, etc,). Remove motor gear cover (approx. 4 screws). Separate shedder main drive gear from motor step up gear by pulling gear out. Turn shredder mechanism up side down to access the cutting blades.
Use an adjustable wrench to turn the main drive gear to see stuck paper. Use a needle noise pliers to remove paper shreds. Repeat step 7 and 8 until all shreds are remove and cutting mechanism move smoothly. Reassembly before testing shredder. If you remove only some of the shreds, the motor may seize up and strip the plastic gears from step up gear. Feb 09, 2009.
Rexel Shredder Service Manual
Whatever business you’re in, there are always going to be documents that you need to dispose of securely. For most offices the easiest, cheapest and most secure way of doing this is to use a shredder, but unfortunately, these are prone to suffering from a paper jam from time to time. The main paper shredder jam causes tend to be:.
Mooney m20e parts manual. Putting in too many sheets of paper. Shredding the wrong materials. Not oiling (lubricating) your shredder Shredder jams can be especially inconvenient when you have a large volume of sensitive material to destroy, plus fixing a shredder’s paper jam can also be a very fiddly and time-consuming business. Here’s our guide to how to unjam a paper shredder, as well as how to minimise the risk of one happening at all.
How to unjam a shredder It’s a familiar situation. You’re half way through a huge pile of paper which needs to be destroyed and suddenly, without any prior warning, the shredder is jammed. But there’s no need to panic, you just need to follow a few simple steps to clear it. Unplug the shredder This is the first and most important part of any attempt at fixing a paper jam. That’s because once you start to investigate the cause it could possibly start working again unexpectedly with potentially very dangerous results for you.
Empty the wastebasket Quite often the simple cause of a jammed shredder is that the wastebasket is full. Empty the wastebasket, reconnect the shredder to the mains and see if this has resolved the problem. Switch to reverse If the shredder jam has still not been solved then try running it in reverse – most have a control that let you do this and it may well shift the blockage. There is, however, a risk that it may make the paper shredder jam a little worse.
If the shredder jams in reverse switch back to auto/forward If it’s now jammed in both directions you should then alternate between working it backwards and forwards as this can often shift the jam after a few attempts. Reduce the thickness of your load before re-shredding Do not feed in more paper than the machine can handle – giving it too much at once can cause paper to get jammed in the blades.
What if my shredder paper jam cannot fix itself? If your shredder cannot unjam itself, you will need to do this manually. Unplug your shredder 2. Remove the top shredding section 3.
Use a pair of tweezers to remove all jammed strands of paper from the blades 4. Cut all curled pieces of paper 5. If plastic is causing the jam, use a screwdriver to clear the block 6. Use shredder oil to lubricate the blades 7. Set the shredder in reverse 8. Feed through a single sheet of paper to see if the jam is cleared Want to know more about how to unjam a shredder?
Our FAQs below has answers to some of the most common queries. How to lubricate a shredder Lubricating your shredder will help prevent jams and allow the paper to smoothly run through. Turn the shredder on 2. Feed a through the shredder 3. Wait for the entire oiled sheet to shred 4. Feed through a few sheets of plain paper to absorb the excess oil 5. Turn off shredder 6.
By hand, apply lubricating oil to the top of the blades 7. Switch shredder on in reverse to evenly distribute oil 8. Feed through a few sheets to absorb any excess oil What should/shouldn’t I feed into the shredder? One of the main reasons why you may have a jammed shredder is down to what you’ve fed into it. Safe to shred Be careful when shredding Paper Credit cards Greetings cards CDs/DVDs Receipts Laminated card Thin cardboard Folded sheets of paper Envelopes Cardboard What other steps can I take to prevent a shredder jam? Feeding paper in too quickly can cause problems so take care to ensure that the machine has completed shredding one batch of paper before you introduce the next.
Another handy tip is to avoid crumpling up paper before you shred it as the machines operate far more efficiently with smooth sheets. Hopefully the tips we’ve given you here will help to make next time your shredder is jammed a little easier to fix. Make sure you safely get rid of your sensitive data – discover our range of today.